Texel Agency

Nippon Topping typically refers to a specialized flooring solution from Nippon Paints, designed for industrial and commercial use.

Epoxy flooring is an ideal choice for pharmaceutical industries, cleanrooms, and laboratories due to its seamless, hygienic, and chemical-resistant properties.

• Corrugated asbestos / metal / non-galvalised corrugated tin roofs
• Sunken
• Rejuvenation of existing bituminous membrane – Hessian / HMHDPE based membrane
• Residential terraces (flat / slope) in substitution of hessian / HMHDPE based membrane

• User friendly, Non-toxic, Green product. 
• Excellent Waterproofing Characteristics. 
• Good crack bridging property 
• Cold applied and hence does not require heating
• Monolithic and Seamless Membrane
• Excellent bonding to concrete
• Can be applied on moist surface also
• Excellent vapour barrier
• Good flexibility and does not crack on aging
• Prevents growth of fungus, algae etc

• Remove all loose gravel, dirt, oil, grease and foreign matter by jet of dry air and clean the surface mechanically or by grinding to make it smooth before application
• Repair all cracks by cutting “V” groove and fill with PMC mortar prepared in the ratio of ShaliCrete : Cement : Sand (1 : 2 : 5)
• Provide 50 mm x 50 mm coving made out of PMC mortar as above.

• Stir TarFelt LM by a slow speed mixture (approx. 400 rpm) fitted with a suitable mixing paddle to ensure a homogenous mix
• After stirring, wait for the product to settle in order to let entrapped air escape

• Slightly damp the surface. Avoid standing water / ponding
• Prime the surface with a mixture of TarFelt LM and potable water in the ratio of 50 : 50 and apply @ 400 grm / m2 of the mixture and allow it to touch dry
• Apply first coat of TarFelt LM @ 0.70 kg / m² by brush / roller / airless spray while the primed surface is tacky. For faster and smoother application, airless spray is preferred
• Spread fiber glass net of 45 gsm with overlaps of 50 mm in both directions when the surface is still tacky
• Allow 1st coat to dry for 10 – 12 hr
• Apply second coat of TarFelt LM @ 0.70 kg / m² by brush / roller / airless spray for final DFT of 1000 micron in two coats inclusive of fiber glass of 45 gsm (theoretical coverage depending on surface conditions)
• Sprinkle sand @ 200 grm / m2 over the final vertical coating when the surface is still tacky to facilitate plastering
• Ensure final curing time of 36 hrs before allowing / carrying out any further work
• Conduct ponding test after 7 days of curing at ambient temperature

• Spread ShaliGeoText 150 gsm with overlap of 50 mm in both directions on fully cured surface
• Protect surface with 50 mm PCC admixed with ShaliPlast LW+ and a gradient of 1 : 100.

• Clean existing surface thoroughly and remove all loose / foreign material
• TarFelt LM shall be applied on prepared surface as per above procedure

• Avoid contact with skin / eyes and avoid swallowing
• Ensure adequate ventilation and avoid inhalation of vapor
• Wear suitable protective clothing, gloves and eye protection
• In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. Do not use solvent to clean the contacted area.
• In case of eye contact, wash immediately with plenty of clean water and seek medical advice
• If swallowed seek medical attention immediately. Do not induce vomiting. 

• This is the most ideal product for repairs and rehabilitation of structures showing hair line cracks.
• It is used to fill up cracks in roof slabs and other areas to make them structurally sound.

• Moisture insensitive
• Low creep characteristics
• High compressive, tensile and flexural strengths
• Fast, convenient pumping
• With stands a wide range of chemicals

Concrete polishing service is a professional flooring treatment that involves mechanically grinding, honing, and polishing a concrete surface to achieve a smooth, shiny, and durable finish. It's commonly used in commercial, industrial, and modern residential spaces for its sleek appearance and low maintenance.